USB-1608G

Unfortunately no, there is no built in feature to re-balance the differential measurement high and low during calibration.

Was this answer helpful? Yes (0) / No (0)

Beginning with InstaCal/Universal Library version 6.60, MCC has enhanced its driver signing (SHA-256). If you are installing on Win7-32 or Win7-64, and if your Windows 7 is not up-to-date, we recommend that you fully run Windows Update prior to installation of our drivers.

Was this answer helpful? Yes (0) / No (0)

Unfortunately there is no DIN rail mount option for this size plastic case. The unit is light, and so Velcro could be used on the bottom of the plastic case (though field wiring could add weight). You could remove the PCB from the plastic case, revealing 4 mounting holes. You could mount the PCB on standoffs. Here is a link to a mechanical drawing: https://www.mccdaq.com/pdfs/drawings/USB-1608G-Series.pdf

Was this answer helpful? Yes (1) / No (0)

We offer two versions of the USB-1608G Series products. The USB-1608G (w/enclosure and screw terminals) and the USB-1608G-OEM (no enclosure and headers). Unfortunately, there is no enclosure available for the -OEM version since the enclosure used on the USB-1608G version would not give access to the headers to allow for signal connections.

Was this answer helpful? Yes (0) / No (0)

In that FAQ, the created application installer is asked to install our InstaCal driver set. But the end-user must still manually run InstaCal (the user must launch inscal32.exe) so that the USB-1608G hardware is assigned a board number (usually board # 0). If the user cannot locate the file named inscal32.exe, then the InstaCal driver set was not installed properly by your installer.

Was this answer helpful? Yes (0) / No (0)

These warnings are because we saved/distribute our VIs in an older version of LabVIEW than you are developing in. Simply re-save the VIs, and then the next time you open your project, you will not get these warnings.

Was this answer helpful? Yes (0) / No (0)

The USB-1608G series provides no ground isolation. The analog and digital circuits each have their own ground planes. This helps with noise reduction in the circuits. However, they eventually come to a single point connection under the ADC. Measurement Computing does offer DAQ products with isolation. Please contact us at 1-800-234-4232 Ext-3 to discuss the options.

Was this answer helpful? Yes (1) / No (0)

Unfortunately, DAQ Assistant will only work with National Instrument’s LabVIEW and NI DAQ products. For help with programming your LabVIEW application using our ULx drivers for LabVIEW, please refer to our KnowledgeBase article “Getting Started with LabVIEW and ULx” here: http://kb.mccdaq.com/Search.aspx?Keywords=Getting%20started%20with%20LabVIEW.

Was this answer helpful? Yes (1) / No (0)

Burstmode is not a setting/choice that is supported by ULx. However, specific to the USB-1608G series, note that when external clock mode is used, it mimic burstmode (i.e. all enabled channels are sampled once per clock pulse). So, if you want to use the on-board (internal clock), then the workaround is to instead wire the timer output of the unit over to its external clock input, specify external clock for the AI, and then start the timer output (using ULx’s counter output VIs) at the desired sample rate.

Was this answer helpful? Yes (0) / No (0)

The trigger on the USB-1608G series accepts only TTL level, digital input (0 to 5 volt logic). The portion of the data sheet that I believe you are referring to describing the “Retrigger” feature… “In retrigger mode, you can set up repetitive analog input trigger events” is referring to the digital trigger event starting your “Analog Input Scan” so as to capture an analog event, triggered by the TRIG input. Unfortunately, you cannot connect an analog trigger signal. However, the “Retrigger” feature will work the way you have described below in that the trigger will rearm itself and wait for the next DIGITAL trigger event to occur to start another acquisition. Excerpt from the ULHELP: Retriggering Use RETRIGMODE with AInScan() to set up repetitive trigger events. Use the ConfigItem option BIADTRIGCOUNT with cbSetConfig() to set the A/D trigger count. When using RETRIGMODE, set the values for the Count argument (cbAInScan()/AInScan()) and the BIADTRIGCOUNT argument (cbSetConfig()/SetAdRetrigCount()) to an integer multiple of the number of channels in the scan. That way, the entire buffer, or the portion of the buffer defined by BIADTRIGCOUNT, will contain updated data.

Was this answer helpful? Yes (1) / No (0)

The USB-1608G is not directly compatible with 4-20 mA signals. It lacks the necessary signal conditioning. However, with the use of a low cost, precision 249 ohm resistor placed across the USB-1608G’s +-5 volt differential inputs you can easily create a current shunt which will produce a 1-5 volt drop across the shunt. With 1 volt equal to 4 mA and 5 volts equal to 20 mA.

Was this answer helpful? Yes (0) / No (0)

The USB-1608G is a multiplexed DAQ device using a single A/D converter. If you need a simultaneous DAQ device, please take a moment to review the following products: USB-1608FS-Plus, USB-1608HS, USB-1602HS, or the USB-1604HS DAQ device.

Was this answer helpful? Yes (3) / No (0)

You can test the digital output function by running the InstaCal Analog Loopback test. Close your 3rd party program before launching InstaCal – then you choose which digital output bit for it to toggle, and you wire (loopback) it to an analog input channel. You should see a square wave on the screen. The amplitude of the digital output is not adjustable. If the digital output toggles properly in InstaCal, then the issue is with your 3rd party program.

Was this answer helpful? Yes (0) / No (0)

Hello - I believe you are referring to NI’s SignalExpress. MCC’s ULX driver is not compatible with SignalExpress. ULx is compatible with the traditional LabVIEW graphical programming environment.

Was this answer helpful? Yes (0) / No (1)

Hello - The USB-1608G will not meet your accuracy requirement of 0.001 volts. The stated accuracy for the +- 10 volt input range is 4075 uV (4.075 mV) and for the +- 5 volt input range is 2266 uV (2.266 mV). To attain a 0.001 volt accuracy you would have to use one of our 24 bit DAQ devices. Like the USB-2404-10. http://www.mccdaq.com/products/product-listing.aspx?oid=1596&r=24 but please do not confuse accuracy with resolution. If you need 0.001 volts of resolution then the USB-1608G will work just fine. Your resolution for the +- 10 volt range would be 0.000305 volts/LSB. I have added a link below to a Knowledge-Base whitepaper on accuracy and resolution. Please do not hesitate to contact MCC with any additional questions. http://kb.mccdaq.com/KnowledgebaseArticle50043.aspx?Keywords=Accuracy

Was this answer helpful? Yes (1) / No (0)

No. The thermocouple generates a tiny voltage, and even with a 24 bit DAQ there is not enough voltage range on the thermocouple to measure it directly with the USB-1608G. Alternatives are to make a thermocouple pre-amplifier to boost the voltage up to a level where it can be directly read by the DAQ. Also DAQs that do measure thermocouples have internal pre-amplifiers, like the USB-2408 Series DAQ. The DAQs that do measure thermocouples also have an internal reference thermocouple.

Was this answer helpful? Yes (0) / No (0)

You should get a USB-TC or USB-TEMP for that. They are designed for reading thermocouples, and give temperature directly. Unlike the USB-1608g they compensate for the temperature-dependent voltage drop due to the mismatch between the terminal on the DAQ and the thermocouple wire.

Was this answer helpful? Yes (2) / No (0)

The USB-1608G was not designed to read thermocouples directly. It lacks 3 things needed: very high gain/amplification, cold junction compensation circuitry, and low pass filtering. Instead choose a product designed with thermocouples in mind, such as the USB-TC or USB-2408.

Was this answer helpful? Yes (0) / No (0)